Rifle & Pistol Reloading Tools & Lubes
LEE – 40 S&W CASE LENGTH GAUGE & SHELLHOLDER
LEE – 40 S&W/10MM CARBIDE 3 DIE SET w/Dipper & #R19 S/H
Product Information
We use a solid carbide insert, ground to a special contour that does not leave a belt mark on the case like other carbide dies. With a carbide sizer, no case lube is needed. Sizer also features an unbreakable decapper and built-in stuck case remover. The Powder Through Expanding Die permits charging the case while expanding the case mouth. The Bullet Seat and Feed Die features a free floating bullet seater to insure maximum accuracy. Includes: Sizer/Decapping Die, Powder Through Expanding Die, Bullet Seat and Feed Die, Shellholder, Powder Dipper and Load Data.
LEE – 45 ACP CARBIDE 3 DIE SET w/Dipper & #R2 S/H
Product Information
We use a solid carbide insert, ground to a special contour that does not leave a belt mark on the case like other carbide dies. With a carbide sizer, no case lube is needed. Sizer also features an unbreakable decapper and built-in stuck case remover. The Powder Through Expanding Die permits charging the case while expanding the case mouth. The Bullet Seat and Feed Die features a free floating bullet seater to insure maximum accuracy.
Includes: Sizer/Decapping Die, Powder Through Expanding Die, Bullet Seat and Feed Die, Shellholder, Powder Dipper and Load Data.
LEE – 45 ACP CARBIDE FACTORY TAPER CRIMP DIE
Product Information
Lee 45 ACP, 45 AUTO RIM, 45 WIN MAG and 45 GAP Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
LEE – 45 ACP CASE LENGTH GAUGE & SHELLHOLDER
LEE – 45 COLT CASE LENGTH GAUGE & SHELLHOLDER
LEE – 45 COLT/454 CASULL CARBIDE FACTORY ROLL CRIMP
Product Information
Lee 45 Colt, 454 Casull, 460 S&W** Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a roll crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
**460 S&W (you can use the # 90865 Carbide Factory Crimp Die for this cartridge to apply a Factory Crimp and post-size part of the case)
LEE – 45-70 GOV’T CASE LENGTH GAUGE & SHELLHOLDER
Product Information
The simplest way to check the case and trim to the correct safe length is with a Lee Case Trimmer. After a case has been loaded a few times, it will stretch beyond maximum length and must be trimmed. The Cutter and Lock Stud (sold separately) works for all calibers. The Case Length Gauge (Pilot) and Shell Holder must be ordered for each caliber. Trim cases by hand or electrically. Can be used with an elecrtric drill to trim, chamfer and polish cases faster. Eliminates danger of long cases. Squares the mouth for more accurate bullet seating and exit. Includes Case Length Gauge and Shellholder only.
LEE – 45-90 SHARPS FACTORY CRIMP DIE
Product Information
Lee 45-90 SHARPS Factory Crimp Die (custom over-run) crimps the bullet in place more firmly than any other tool. Tests demonstrate that even bullets which have no crimp groove will shoot more accurately. A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move. This higher start pressure insures a more uniform pressure curve and less velocity variation.
LEE – 6.8 WESTERN 3 DIE SET w/FACTORY CRIMP w/Dipper & #R5 S/H Very LTD. Production
Product Information
Lee PaceSetter Dies now include the exclusive Lee Factory Crimp Die to produce factory-like ammunition with improved utility and accuracy. The die set also includes a conventional bullet seater and roll crimper. You can choose the type of crimp you desire. They also include a shell holder, powder dipper, load data and storage box. Please note, there is no load data available for this cartridge, a dipper is not included.
LEE – 6mm REM CASE LENGTH GAUGE & SHELLHOLDER
