Rifle & Pistol Reloading Tools & Lubes
Hornady Reloading Counter Mat 17″ x 26″
Product Information:
The Hornady Reloading Counter Mat is the ultimate reference tool for your reloading bench. This non-skid bullet mat features the entire line of Hornady bullets with corresponding caliber, diameter, weight, ballistic coefficient, sectional density and Hornady's item number. The Counter Mat also doubles as a cleaning and maintenance mat, protecting your work bench from solvents and oils. The slick plastic finish on the mat will not absorb solvents and oils, and cleans up quickly. If you are a serious reloader, pick up your Hornady Reloading Counter Mat today. Features- Features Hornady's full line of bullets!
- Non-skid neoprene back
- Slick plastic top
HORNADY S/H #12: 25 REMINGTON/30 30/6.8 REMINGTON SPC/32 REMINGTON
Product Information
Hornady Shell Holders are precision machined from solid steel then heat treated to perform flawlessly for the life of the press. Hornady steel shell holders also fit most other brands of reloading presses.
Fits:
- 219 Zipper
- 22/30-30 Winchester
- 22/30-30 Ackley Improved 40-Degree Shoulder
- 5.6x52mm Rimmed (22 Savage High-Power)
- 6mm/30-30 Winchester
- 6mm/30-30 Winchester Ackley Improved 40-Degree Shoulder
- 25-35 WCF
- 7-30 Waters
- 7-30 Waters Ackley Improved 40-Degree Shoulder
- 30-30 Winchester
- 30-30 Winchester Ackley Improved 40-Degree Shoulder
- 300 Herrett
- 7.5mm Schmidt Rubin (7.5 x 55 Swiss)
- 8.15x46Rmm
- 8.15x46mm Rimmed (318 Diameter)
- 32-40 WCF
- 32 Winchester Special
- 35/30-30 Winchester
- 375 Winchester
- 38-55 WCF
HORNADY S/H #5: “BELTED MAGS” WEATHERBY’s/7mm MAG/300 MAG…
Product Information
Precision machined from solid steel then heat treated to perform flawlessly for the life of the press. They fit all other Hornady accessories including the Hornady Cam-Lock Case Trimmer and Hand-Held Priming Tool. These shellholders will also fit the presses of most other brands in the industry. Fits the following calibers:
|
|
HORNADY SEATING STEM for .224 A-TIP/ELD MATCH BULLET
Hornady Shell Holder #45 45 ACP/45 Win Mag
Product Information
Precision machined from solid steel, then heat treated to perform flawlessly for the life of the press. They fit all other Hornady accessories (Case Trimmer, Hand-Held Priming Tool, etc.) so there are no special shellholders to buy. Also fits most other brands of reloading presses. Fits the following calibers: Fits:- 45acp
- 45 Winchester Magnu
Hornady Shell Plate #14 33 Winchester/338-378 Weatherby Magnum/416/460 Weatherby Magnum/ 45-70 Govt/475/480 Ruger
Product Information
The Hornady Lock-N-Load AP Progressive Press Shellplate makes changing calibers a breeze on your Hornady Lock-N-Load Press and the older Hornady Projector Press. There is a shellplate available to fit almost every caliber. The shellplate numbers correspond with the Hornady shellholder numbers for different calibers. These shellplates are designed to work with the EZ-Ject System and Pro-Jector presses.
Fits:
- 33 Winchester
- 378 Weatherby
- 416 Weatherby
- 460 Weatherby
- 45-70 Government
- 475 Linebaugh
- 480 Ruger
Hornady Shellplate #8: 30Luger/9mm Luger/9×21/9×18/38Sup Auto
INLINE FABRICATION QUICK CHANGE STORAGE DOCK DOUBLE
LEE – 40 S&W/10mm Carbide Factory Crimp Die
Product Information
Lee 40 S&W/10mm Auto Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
LEE – 40 S&W/10mm Carbide Taper Crimp Die
The Lee Taper Crimp Die is hardened steel designed to overcome crimp problems caused by poor die design. These dies offer little or no advantage when used with 1986 or newer Lee dies as the crimp angle is already a modified taper crimp. Jacketed bullets must have a crimp groove (cannelure). Shellholder sold separately. Comes shipped with a plastic storage case.
LEE – 25-35 WCF CASE LENGTH GAUGE & SHELLHOLDER
Product Information
The simplest way to check the case and trim to the correct safe length is with a Lee Case Trimmer. After a case has been loaded a few times, it will stretch beyond maximum length and must be trimmed. The Cutter and Lock Stud (sold separately) works for all calibers. The Case Length Gauge (Pilot) and Shell Holder must be ordered for each caliber. Trim cases by hand or electrically. Can be used with an electric drill to trim, chamfer and polish cases faster. Eliminates danger of long cases. Squares the mouth for more accurate bullet seating and exit. Includes Case Length Gauge and Shellholder only. Lee 25-35 WCF Case Length Gauge is a precise, easy way to trim to length and square the case mouth.
LEE – .223 REM ULTIMATE 4 DIE SET, S/H #4
Product Information
Choose this die set for maximum versatility.
The set features a full length-resizing die to return brass to factory new dimensions, perfect for reloading brass fired in other guns. The Collet Neck sizing die is used on your fire formed brass giving you best possible accuracy. No case lube required and cases last almost forever. The Easy Adjust Dead Length Bullet seating die fool-proofs the bullet seating adjustment, and assures perfect seating depth every time. The Factory Crimp die provides a secure crimp on bullets with or without a crimp groove. In most cases it helps accuracy by providing a uniform higher start pressure and gives the finished cartridge Factory like accuracy and dependability. The set is complete, with shell holder, powder measure and famous Lee load data featuring all common brands of powder organized in a easy to read logical format.
Includes:
•Full length resizing Die
•Collet Neck sizing Die
•Easy adjust dead length bullet Seating Die
•Factory Crimp Die
•Shell holder, Powder measure, & Lee load data
