Shotshell Reloading Components
BPI TRIM DOCTOR 2 20ga w/ EXACTA-TRIM BUSHING
Product Information
Two tools in one:
- Â Shotshell case length trimmer that produces exacting cuts and ideal short cases
-
Case disassembly tool
After years of searching the world for just the right case trimmer without success, our ballistic technicians demanded that BPI make this convenient and necessary tool. A threaded adjustment gauge in the Trim Doctor holds shells in alignment to produce a clean and crimpable edge. The Trim Doctor is designed to remove 1/4″ at a time (about the same as full fold crimp): 3″ shells become 2-3/4″, 2-3/4″ become 2-1/2″. Two full cuts on a 10 gauge shell produce a 2-7/8″ shell. Select the gauge of your new Trim Doctor; it comes with one gauge adaptor bushing.
Our new ExactaTrim adaptor bushings assure tight cuts with no spiraling and they are available in additional sizes to make your Trim Doctor even more versatility.
As a shell disassembly tool, the Trim Doctor works on any gauge, 10ga through .410. Just remove the threaded guide, insert loaded shell into opening and gently turn the shell while applying slight pressure to the blade guide. The top of shell will pop off cleanly after a few turns.
The Trim Doctor will pay for itself many times over by allowing you to retrieve components from reject shells and by allowing further firings out of many hulls with tired crimps.
NOTE: Does not include different bushings. Must purchase separately.
BPI WAD 12ga HCD #21 1oz TO 1-1/8oz LEAD 250/BAG
Product Information
The pliable Helix cushioning system is designed to reduce recoil and shock. Superb 1-1/8oz to 1-1/4oz. patterns, optimum range of 30-65 yards. An excellent wad for handicap trap shooting and field loads.
SPECIFICATIONS:
- Gas Seal: arched dome .725" diameter, .215" thick - two powder migration rings and two stabilization rings
- Overall length: 1.6"
- Seal to cup bottom: .900"
- Shotcup depth: .740"
- Shotcup type: lay-back hinged
- Shot level in cup: 1oz+
- Optimum range: 30-65 yards
- Going away targets
BPI WAD 12ga HCD #24 7/8 TO 1oz LEAD 250/BAG
Product Information
Predominantly a 1-ounce wad, but also used with some 7/8-oz. loads. The soft, pliable cushion system is designed to provide the shooter with reduced recoil and to allow a wide range of load adjustment with a consistent level of wad pressure resistance. The "vacuum-trap" anti-powder migration ring is the outstanding feature of this wad, making it an excellent choice for straight-walled hulls such as Fiocchi
|
BPI WAD 20ga CSD 1oz UNSLIT STEEL 250/BAG
Product Information
The CSD series of wads offer wide array of capacity options along with a revolutionary energy-absorbing cushion system. These multi-capacity, barrel protecting shotcups are designed for steel, tungsten, and large capacity lead field loads.
The CSD wad series combines easy loading with high performance results. CSD wads are not pre-slit. Ballistic Products recommends their Stainless Steel Wad Snips to cut the number of petals best suited for your shooting and intended range.
BPI WAD 28ga TPS NON-TOX 5/8 STEEL 3/4 ITX 100/BG
The TPS 28ga is a full-length shot column designed specifically for the rigors of modern non-toxic shot, like steel, ITX, and Hevi-Shot. Finally, a wad that will allow you to load almost any type of non-toxic shot for your modern 28ga shotgun. Designed for magnum field loads, the TPS 28 is the grand result of over two years of development.
Maximum capacities of smaller shot sizes are 1 oz. ITX Extreme-13 shot, 7/8 oz. ITX Original-10 shot, and 3/4 oz. steel shot. Capacity will vary greatly according to pellet size and these maximum weights will not necessarily yield the best loads; only testing results will render that decision.
- Length = 1.770"
- Depth = 1.632"
- Gas seal diam. = 0.546"
- Gas seal depth = 0.085"
- Wall thick. = 0.025" to 0.055"
Budget Shooter .410 Overshot cards 500 / bag
Product Information
Place an overshot card on top of the shot charge just before crimping to improver overall crimp quality and seal in small shot and/or buffer. Excellent for use with BPI Roll Crimpers.
- Overshot cards produce flatter, tighter crimps
- More consistent load combustion and pellet containment
- Effectively contains pellets within the shotcup during the firing cycle
- Water-repellant
- Seals buffer within the shell
- Excellent for roll crimps
CCI – Primers #209 Shotshell /1000
CCI Primers are continuously tested and improved. As a result today's CCI primers are more sensitive, easier to seat and more compatible with progressive and automated loading equipment than ever before. They utilize modern non-corrosive and non-mercuric initiator mixes for the cleanest burn possible.
Primers are only shipped by Canpar Courier, Canpar does not deliver to PO Boxes. Please DO NOT select Canada Post as your shipping method if your order contains this item.
CCI – Primers #209 Shotshell 100/Sleeve
CCI Primers are continuously tested and improved. As a result today's CCI primers are more sensitive, easier to seat and more compatible with progressive and automated loading equipment than ever before. They utilize modern non-corrosive and non-mercuric initiator mixes for the cleanest burn possible.
Primers are only shipped by Canpar Courier, Canpar does not deliver to PO Boxes. Please DO NOT select Canada Post as your shipping method if your order contains this item.
Cheddite – Shotshell 209 PRIMER 100/Sleeve
Product Information
To improve ballistic performances with most available powders, Cheddite has developed its dependable and powerful Clerinox primer (US type). The regularity of Cheddite primers provide a reliable powder ignition at optimum sensitivity will allow your cartridges to perform to your expectations. This regularity is obtained thanks to a strict quality control of all components : anvil, chamber, cap, mixture and to a continuous performance checking of the primer itself as well as when combined with a specific reference cartridge loading.
CHEDDITE HULL (Troy) 12ga 2.75″ 12mm Unprimed Blue 100/Bag
CHEDDITE HULL (Troy) 12ga 2.75″ 12mm Unprimed Green 100/Bag
CHEDDITE HULL 20ga 2.5″ 8mm PRIMED YELLOW PER 100
Product Information
Cheddite is the largest producer of shotgun hulls in the world. Imported from France, they are straight-walled which requires the use of wads designed for straight-walled hulls which are available from a number of manufacturers including Claybuster, Federal, and Downrange.
Fully reloadable, primed hulls. This is not loaded ammunition.
