Press & Die Parts
LEE 6.5×55 Swedish Mauser EZ X EXPANDER/DECAPPER
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
LEE EZ X EXPANDER 30 CAL LONG SE2277
Product Information
Replacement expander/decapping rod. For use with Lee dies only. Part SE2277 for product LOAD-MASTER 30/06 Will Fit:90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
LEE EZ X EXPANDER 303 B, 7.62X54R
LEE SPLINE DRIVE BREECH LOCK BUSHING 4-PACK
Product Information
Spline drive Breech Lock Bushings 4 pack. New, easy grip splined drive surface allows easy, accurate and fast die installation in your press. Reloading dies are confusingly similar looking, so we anodized and colored the bushings so you can “color code” your dies for quick positive identification. No need for lock rings on your dies with these quick-change bushings. Simply lightly tighten the clamp screw, and split collar will put a vice lock on your die. Loosen the screw, and the die will spin freely. Once set you’ll never lose position. They look so good and work so well, you’ll want them for all your dies.
LEE SQUARE RATCHET
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
LEE ULTIMATE LOCK RINGS 3-PACK
Product Information
Lee ultimate spline drive lock rings. 3 pack of gold anodized aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with custom extrusion of high strength aluminum with a splined exterior surface. We split the ring, and added a cross bolt that when even lightly tightened, applies a vice like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.- Compatible with 7/8 x 14 threaded Lee reloading dies and Lee reloading presses.
- Torque type splined exterior, for a no-slip grip.
- "O" ring, anti-rotation, included. Never loosens during use.
- Lock-ring wrench included.
LEE UNDERSIZE MANDREL .3035
Product Information
UNDERSIZE MANDREL .3035
When delivered from the factory, the collet die will grip the bullet with a light press fit with cases of average hardness. Should you desire a tighter fit, you can order this (.3035") undersized mandrel for 300 WSM, 7.5x55, 30/06, 30/30, 308 Win, and 300 Win Ma
RCBS Expander-Decapping Unit .375 cal
These replacement decapping units feature an expander rod, expander ball, and decapping pin. They are used in sizing dies to de-prime the case and expand the case neck in bottleneck cartridges. It is always a good idea to keep an extra decapping unit on-hand so you can ensure your reloading sessions do not get interrupted if you ever damage them during use.
- Factory Replacement Part
- Precision Machined to ensure concentricity
- Expander Rod, Expander Ball and Decapping Pin
- 0.375
- Limited Lifetime Warranty
