Rifle & Pistol Reloading Tools & Lubes
LEE – Undersized Carbide Sizing Die 9mm Luger
Product Information
Lee U Carbide Small Base Sizing Dies are great for reloaders looking for ultimate feeding reliability in their handgun. These dies undersize brass between .002″ and .003″ smaller than other Lee Carbide Sizing dies. Ammunition with undersized brass cases will chamber each and every time it is loaded out of a magazine giving reliable chambering each time a round is stripped out of the magazine or loaded into a cylinder. Competition shooters rely on having ammunition that will feed and chamber each round of ammunition as it is stripped out of the magazine. One of the other benefits reloaders have reported when using Lee U dies is increased consistency and accuracy in loaded rounds because these dies help increase and provide more consistent neck tension on loaded bullets. The solid carbide insert inside of these dies is ground to a special contour that does not leave a belt mark on the case. These carbide dies do not require lubricant while resizing, though a little case lube will make the sizing process easier. Shellholder sold separately.
Technical Information:
Material: Steel
Die Type: U Carbide Small Base Sizing Die
Accessories: Plastic Storage Container
Notes:
•Carbide sizing dies do not require case lube
•Undersized dies size brass between .002″ and .003″ below SAAMI specifications, so ammunition will feed in chamber in tight chambers
•Undersized dies work great for bringing back case tension to hold bullets on cases that may be thinner walled
LEE – UNIVERSAL DECAPPING DIE FOR UNDERSIZE FLASH HOLE
LEE 1 1/4″-12 BREECH LOCK UPDATE KIT 1.25×12 THREAD
Product Information
- 1 1/4"-12 breech lock adapter
- Spline drive lock-ring eliminator
- Lock-ring wrench
- Lee Precision Classic Cast®
- Hornady® Iron®
- Hornady® Classic™ / Lock-N-Load®
- RCBS Rock Chucker® Supreme
- Redding Big Boss®
- Redding® 700 Ultramag
- ..and more (verify your removable press bushing/adapter size is 1 1/4"-12)
LEE 22 HORNET CASE LENGTH GAUGE & SHELLHOLDER
Product Information
The simplest way to check the case and trim to the correct safe length is with a Lee Case Trimmer. After a case has been loaded a few times, it will stretch beyond maximum length and must be trimmed. The Cutter and Lock Stud (sold separately) works for all calibers. The Case Length Gauge (Pilot) and Shell Holder must be ordered for each caliber. Trim cases by hand or electrically. Can be used with an elecrtric drill to trim, chamfer and polish cases faster. Eliminates danger of long cases. Squares the mouth for more accurate bullet seating and exit. Includes Case Length Gauge and Shellholder only.
LEE 22 HORNET FACTORY CRIMP DIE
LEE 22 HORNET QUICK TRIM DIE
Product Information:
LEE 22-250 QUICK TRIM DIE
Product Information:
Lee 22-250 Rem Pacesetter 3-Die Set
Product Information
Each Lee Precision has been manufacturing high quality, affordable reloading equipment since 1958. Each Pacesetter 3-Die Set includes the exclusive Lee Factory Crimp Die, Full Length Sizer Die and Bullet Seater Die. Each set is made from steel and includes the appropriate Shellholder, Powder Measure, load data, plastic storage box and a two year warranty. Adjustable crimp from slight taper to full roll.
LEE 22-250 REMINGTON COLLET DIE ONLY
Product Information
LEE 223 EZ X EXPANDER/DECAPPER
LEE 223 REMINGTON COLLET DIE ONLY
Product Information
A collet squeezes the case neck against a precision mandrel for a perfect fit with minimum run-out. No lube case is needed and neck sizing extends case life. This dies sizes only the neck to preserve the perfect fit of fire forming. Only reload cases that have been fired in your gun. Not recommended for autoloaders, slide or lever action guns. Includes: Collet neck sizing die only.
LEE 243 WINCHESTER FACTORY CRIMP DIE
Product Information
The Lee Precision Factory Crimp Die is designed to give reloaders the perfect crimp on each round of reloaded ammunition. The Factory Crimp Die crimps the bullet more firmly in place than any other die with more uniform pressure. The Factory Crimp Die features a collet that squeezes the case mouth into the crimping groove for a firm hold. It is nearly impossible to buckle the case when crimping when compared to a regular roll crimp die. Lee’s testing has shown that using a Factory Crimp Die provides a more uniform pressure curve, increasing the accuracy of any bullet. Shellholder sold separately.
Technical Information:
Material: Steel
Fits: Reloading presses that accept standard 7/8”-14 Threads
Accessories:
•Plastic Storage Box
