Hornady – LOCK-N-LOAD DIE BUSHING (2-PACK)
$25.00
Product Information
Lock-N-Load lets you switch from one die to another and begin reloading in seconds. No threading dies in and out or adjusting is necessary. The positive locking action of the bushings holds the dies in rock solid, perfect alignment. You’ll want a Lock-N-Load bushing for every die you use.
This is a 2 Pak.
5 in stock
Product Information
Lock-N-Load lets you switch from one die to another and begin reloading in seconds. No threading dies in and out or adjusting is necessary. The positive locking action of the bushings holds the dies in rock solid, perfect alignment. You’ll want a Lock-N-Load bushing for every die you use.
This is a 2 Pak.
| Weight | 0.3 lbs |
|---|---|
| Brand |
Hornady |
Only logged in customers who have purchased this product may leave a review.
Related products
Hornady Reloading Counter Mat 17″ x 26″
Product Information:
The Hornady Reloading Counter Mat is the ultimate reference tool for your reloading bench. This non-skid bullet mat features the entire line of Hornady bullets with corresponding caliber, diameter, weight, ballistic coefficient, sectional density and Hornady's item number. The Counter Mat also doubles as a cleaning and maintenance mat, protecting your work bench from solvents and oils. The slick plastic finish on the mat will not absorb solvents and oils, and cleans up quickly. If you are a serious reloader, pick up your Hornady Reloading Counter Mat today. Features- Features Hornady's full line of bullets!
- Non-skid neoprene back
- Slick plastic top
LEE – CASE COLLATOR FUNNEL
Product Information
The Lee Case Collator can fill all four Lee Case Feeder Tubes in just 10 seconds. Brass falls base down into the drop tubes, making progressive reloading with the Pro1000 or Load-Master presses that much easier. To use lay cases in collator and they will fall base down into the drop tubes (not included)
LEE – Roller Handle Upgrade Kit
Product Information
Pro 1000 and Turret Press roller handle upgrade kit includes everything you need to upgrade your ball grip to an ergonomic foam roller handle grip and all steel linkage. This handle can not be used on the Classic Turret Press, Breech Lock Classic Cast, Classic Cast, Load-Master or Reloader Press NOTE: This handle upgrade does NOT work on the Classic Cast Turret Press or the Classic Cast ''O'' Frame Presses.
LEE – TURRET 3-HOLE FOR TURRET PRESS/PRO 1000
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE EZ X EXPANDER 30 CAL LONG SE2277
Product Information
Replacement expander/decapping rod. For use with Lee dies only. Part SE2277 for product LOAD-MASTER 30/06 Will Fit:90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
RCBS Expander-Decapping Unit .375 cal
- Factory Replacement Part
- Precision Machined to ensure concentricity
- Expander Rod, Expander Ball and Decapping Pin
- 0.375
- Limited Lifetime Warranty
Reviews
There are no reviews yet.