LEE EZ X EXPANDER 30 CAL LONG SE2277
$7.00
Product Information
Replacement expander/decapping rod. For use with Lee dies only.
Part SE2277 for product LOAD-MASTER 30/06
Will Fit:
90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
9 in stock
Product Information
Replacement expander/decapping rod. For use with Lee dies only.
Part SE2277 for product LOAD-MASTER 30/06
Will Fit:
90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
| Weight | .1 lbs |
|---|
Related products
Hornady – DELUXE DIE WRENCH
Product Information
The Hornady Lock-N-Load Deluxe Die Locking Ring Wrench is an ideal tool for your Lock-N-Load AP Press or for any Hornady die sets. The wrench is designed to hold the shellplate in place and keep it from slipping when adjusting the plate and securing it to the press. It also has three flats for tightening dies, spindle locks, and lock rings.
Hornady Reloading Counter Mat 17″ x 26″
Product Information:
The Hornady Reloading Counter Mat is the ultimate reference tool for your reloading bench. This non-skid bullet mat features the entire line of Hornady bullets with corresponding caliber, diameter, weight, ballistic coefficient, sectional density and Hornady's item number. The Counter Mat also doubles as a cleaning and maintenance mat, protecting your work bench from solvents and oils. The slick plastic finish on the mat will not absorb solvents and oils, and cleans up quickly. If you are a serious reloader, pick up your Hornady Reloading Counter Mat today. Features- Features Hornady's full line of bullets!
- Non-skid neoprene back
- Slick plastic top
LEE – TURRET 4-HOLE FOR TURRET PRESS
Product Information
The Lee Turret Press is a proven design utilizing replaceable turrets that lock into a solid steel ring. One of the best features is the ability to simply lift out an entire turret and replace it with the another turret setup to load a different caliber. These extra turrets give reloaders the ability to have all of their different calibers on a different turret ready to load. Technical Information: Fits: Lee 4 Hole, Classic 4 Hole Turret Press Function: Replacement Turret Notes: 7/8"-14 Threaded dies
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE SPLINE DRIVE BREECH LOCK BUSHING 4-PACK
Product Information
Spline drive Breech Lock Bushings 4 pack. New, easy grip splined drive surface allows easy, accurate and fast die installation in your press. Reloading dies are confusingly similar looking, so we anodized and colored the bushings so you can “color code” your dies for quick positive identification. No need for lock rings on your dies with these quick-change bushings. Simply lightly tighten the clamp screw, and split collar will put a vice lock on your die. Loosen the screw, and the die will spin freely. Once set you’ll never lose position. They look so good and work so well, you’ll want them for all your dies.
RCBS Expander-Decapping Unit .375 cal
- Factory Replacement Part
- Precision Machined to ensure concentricity
- Expander Rod, Expander Ball and Decapping Pin
- 0.375
- Limited Lifetime Warranty
