LEE SQUARE RATCHET
$2.00
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4″x 1/4″ steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
In stock
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4″x 1/4″ steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
| Weight | .01 lbs |
|---|
Related products
Hornady – LOCK-N-LOAD DIE BUSHING (2-PACK)
Product Information
Lock-N-Load lets you switch from one die to another and begin reloading in seconds. No threading dies in and out or adjusting is necessary. The positive locking action of the bushings holds the dies in rock solid, perfect alignment. You'll want a Lock-N-Load bushing for every die you use. This is a 2 Pak.
LEE – BENCH PLATE
Product Information
Lee Bench Plate allows for quick press removal without unbolting from bench. Includes 1 steel base block that fits all current Lee metallic presses. Special elevator bolt hardware included. Powder coated, thick steel mounts quickly and securely to any bench or tabletop. Wide steel plate distributes load, adding rigidity to the lightest bench top.
LEE – Roller Handle Upgrade Kit
Product Information
Pro 1000 and Turret Press roller handle upgrade kit includes everything you need to upgrade your ball grip to an ergonomic foam roller handle grip and all steel linkage. This handle can not be used on the Classic Turret Press, Breech Lock Classic Cast, Classic Cast, Load-Master or Reloader Press NOTE: This handle upgrade does NOT work on the Classic Cast Turret Press or the Classic Cast ''O'' Frame Presses.
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE BULLET SEATING MICRO- METER ADJ SCREW – HANDGUN
Product Information
- Easy to use: Simply remove your existing adjustment screw, and thread in the micrometer.
- Infinite adjustment: Allows you to set your bullet seating depth precisely.
- Economically priced: You'll want one for every die
LEE EZ X EXPANDER 30 CAL LONG SE2277
Product Information
Replacement expander/decapping rod. For use with Lee dies only. Part SE2277 for product LOAD-MASTER 30/06 Will Fit:90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
LEE ULTIMATE LOCK RINGS 3-PACK
Product Information
Lee ultimate spline drive lock rings. 3 pack of gold anodized aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with custom extrusion of high strength aluminum with a splined exterior surface. We split the ring, and added a cross bolt that when even lightly tightened, applies a vice like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.- Compatible with 7/8 x 14 threaded Lee reloading dies and Lee reloading presses.
- Torque type splined exterior, for a no-slip grip.
- "O" ring, anti-rotation, included. Never loosens during use.
- Lock-ring wrench included.
