LEE 223 EZ X EXPANDER/DECAPPER
$5.00
Product Information
Replacement expander/decapping rod. For use with Lee dies only.
Will Fit:
5.56mm / 223 Rem.
.223 Ackley
.223 WSSM
22-250 Rem.
22-250 Ackley
220 Swift
222 Rem.
14 in stock
Related products
Hornady – DELUXE DIE WRENCH
Product Information
The Hornady Lock-N-Load Deluxe Die Locking Ring Wrench is an ideal tool for your Lock-N-Load AP Press or for any Hornady die sets. The wrench is designed to hold the shellplate in place and keep it from slipping when adjusting the plate and securing it to the press. It also has three flats for tightening dies, spindle locks, and lock rings.
Hornady – LOCK-N-LOAD DIE BUSHING (2-PACK)
Product Information
Lock-N-Load lets you switch from one die to another and begin reloading in seconds. No threading dies in and out or adjusting is necessary. The positive locking action of the bushings holds the dies in rock solid, perfect alignment. You'll want a Lock-N-Load bushing for every die you use. This is a 2 Pak.
LEE – CASE COLLATOR FUNNEL
Product Information
The Lee Case Collator can fill all four Lee Case Feeder Tubes in just 10 seconds. Brass falls base down into the drop tubes, making progressive reloading with the Pro1000 or Load-Master presses that much easier. To use lay cases in collator and they will fall base down into the drop tubes (not included)
LEE EZ X EXPANDER 30 CAL LONG SE2277
Product Information
Replacement expander/decapping rod. For use with Lee dies only. Part SE2277 for product LOAD-MASTER 30/06 Will Fit:90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
LEE SQUARE RATCHET
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
LEE STEEL BASE BLOCK FOR BENCH PLATE SYSTEM
Product Information:
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
RCBS Expander-Decapping Unit .375 cal
These replacement decapping units feature an expander rod, expander ball, and decapping pin. They are used in sizing dies to de-prime the case and expand the case neck in bottleneck cartridges. It is always a good idea to keep an extra decapping unit on-hand so you can ensure your reloading sessions do not get interrupted if you ever damage them during use.
- Factory Replacement Part
- Precision Machined to ensure concentricity
- Expander Rod, Expander Ball and Decapping Pin
- 0.375
- Limited Lifetime Warranty
