LEE STEEL BASE BLOCK FOR BENCH PLATE SYSTEM
$22.00
Product Information:
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
1 in stock
Product Informatio25
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
| Weight | 1.2 lbs |
|---|
Related products
LEE – BENCH PLATE
Product Information
Lee Bench Plate allows for quick press removal without unbolting from bench. Includes 1 steel base block that fits all current Lee metallic presses. Special elevator bolt hardware included. Powder coated, thick steel mounts quickly and securely to any bench or tabletop. Wide steel plate distributes load, adding rigidity to the lightest bench top.
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE SQUARE RATCHET
Product Information
LEE ULTIMATE LOCK RINGS 3-PACK
Product Information
Lee ultimate spline drive lock rings. 3 pack of gold anodized aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with custom extrusion of high strength aluminum with a splined exterior surface. We split the ring, and added a cross bolt that when even lightly tightened, applies a vice like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.- Compatible with 7/8 x 14 threaded Lee reloading dies and Lee reloading presses.
- Torque type splined exterior, for a no-slip grip.
- "O" ring, anti-rotation, included. Never loosens during use.
- Lock-ring wrench included.
