LEE – PRIMER EXPLOSION DEFLECTOR FOR LOADMASTER
$12.00
For the Lee Loadmaster Progressive Press. Necessary if using primers other than CCI or Winchester brand.
2 in stock
Related products
Hornady – LOCK-N-LOAD DIE BUSHING (2-PACK)
Product Information
Lock-N-Load lets you switch from one die to another and begin reloading in seconds. No threading dies in and out or adjusting is necessary. The positive locking action of the bushings holds the dies in rock solid, perfect alignment. You'll want a Lock-N-Load bushing for every die you use. This is a 2 Pak.
LEE – CASE COLLATOR FUNNEL
Product Information
The Lee Case Collator can fill all four Lee Case Feeder Tubes in just 10 seconds. Brass falls base down into the drop tubes, making progressive reloading with the Pro1000 or Load-Master presses that much easier. To use lay cases in collator and they will fall base down into the drop tubes (not included)
LEE – TURRET 3-HOLE FOR TURRET PRESS/PRO 1000
The Lee Turret Press is a proven design utilizing replaceable turrets that lock into a solid steel ring. One of the best features is the ability to simply lift out an entire turret and replace it with the another turret setup to load a different caliber. These extra turrets give reloaders the ability to have all of their different calibers on a different turret ready to load.
Technical Information:
Fits: Lee 3 Hole, Classic 3 Hole Turret Press
Function: Replacement Turret
Notes: 7/8"-14 Threaded dies
LEE BULLET SEATING MICRO- METER ADJ SCREW – RIFLE
Product Information
Lee Bullet Seating Micrometer Adjust Screw - Rifle
Set your bullet seating depth in .001" increments with Lee's new Bullet Seating Micrometer Adjust Screw. Infinitely adjustable, allows precision seating depth. Eliminates annoying clicks that prevent splitting thousandths. No clicks, just smooth. Black anodized, laser etched scale allows you to easily and quickly set your depth, and achieve repeatable results round after round. Works on all Lee bullet seating dies.
- Easy to use: Simply remove your existing adjustment screw, and thread in the micrometer.
- Infinite adjustment: Allows you to set your bullet seating depth precisely.
- Economically priced: You'll want one for every die
LEE SQUARE RATCHET
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
LEE STEEL BASE BLOCK FOR BENCH PLATE SYSTEM
Product Information:
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
LEE ULTIMATE TURRET PRESS 5 HOLE TOOL HEAD
5 hole turret and index rod for the Ultimate Turret Press or Ultimate Turret Press Kits. The round tool carrier is precision machined on all surfaces. Each die position is machined to accept any Lee Breech lock bushing.
Reviews
There are no reviews yet.