LEE – AUTO DISK RISER
$13.50
Product Information
The Lee Auto-Disk Riser allows use of other brands of dies that have extended adjusting screws and provides clearance for the Lee Safety Prime.
5 in stock
Product Information
The Lee Auto-Disk Riser allows use of other brands of dies that have extended adjusting screws and provides clearance for the Lee Safety Prime.
| Weight | 0.3 lbs |
|---|---|
| Brand |
LEE |
Only logged in customers who have purchased this product may leave a review.
Related products
Hornady – DELUXE DIE WRENCH
Product Information
The Hornady Lock-N-Load Deluxe Die Locking Ring Wrench is an ideal tool for your Lock-N-Load AP Press or for any Hornady die sets. The wrench is designed to hold the shellplate in place and keep it from slipping when adjusting the plate and securing it to the press. It also has three flats for tightening dies, spindle locks, and lock rings.Hornady – LNL AP CASE RETAINER SPRING 3 PACK
LEE – Roller Handle Upgrade Kit
Product Information
Pro 1000 and Turret Press roller handle upgrade kit includes everything you need to upgrade your ball grip to an ergonomic foam roller handle grip and all steel linkage. This handle can not be used on the Classic Turret Press, Breech Lock Classic Cast, Classic Cast, Load-Master or Reloader Press NOTE: This handle upgrade does NOT work on the Classic Cast Turret Press or the Classic Cast ''O'' Frame Presses.LEE – TURRET 4-HOLE FOR TURRET PRESS
Product Information
The Lee Turret Press is a proven design utilizing replaceable turrets that lock into a solid steel ring. One of the best features is the ability to simply lift out an entire turret and replace it with the another turret setup to load a different caliber. These extra turrets give reloaders the ability to have all of their different calibers on a different turret ready to load. Technical Information: Fits: Lee 4 Hole, Classic 4 Hole Turret Press Function: Replacement Turret Notes: 7/8"-14 Threaded diesLEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE EZ X EXPANDER 30 CAL LONG SE2277
Product Information
Replacement expander/decapping rod. For use with Lee dies only. Part SE2277 for product LOAD-MASTER 30/06 Will Fit:90880 RGB DIE SET 30/06 SPRINGFIELD
90881 RGB DIE 300 WIN MAG
90732 PACESETTER DIES 7.65 Argentine Mauser
90508 PACESETTER DIE SET 30/06
90539 PACESETTER DIE SET 300 WIN MAG
90615 DELUXE 3 DIE SET 30/06
90616 DELUXE 3 DIE SET 300 WIN MAG
LEE ULTIMATE LOCK RINGS 3-PACK
Product Information
Lee ultimate spline drive lock rings. 3 pack of gold anodized aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with custom extrusion of high strength aluminum with a splined exterior surface. We split the ring, and added a cross bolt that when even lightly tightened, applies a vice like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.- Compatible with 7/8 x 14 threaded Lee reloading dies and Lee reloading presses.
- Torque type splined exterior, for a no-slip grip.
- "O" ring, anti-rotation, included. Never loosens during use.
- Lock-ring wrench included.

Reviews
There are no reviews yet.