Hornady Neck Turn Mandrel .17 cal
$10.00
Designed for use with the Hornady Neck Turn Tool (#41224).
Diameter: 0.172
1 in stock
Related products
LEE – TURRET 3-HOLE FOR TURRET PRESS/PRO 1000
The Lee Turret Press is a proven design utilizing replaceable turrets that lock into a solid steel ring. One of the best features is the ability to simply lift out an entire turret and replace it with the another turret setup to load a different caliber. These extra turrets give reloaders the ability to have all of their different calibers on a different turret ready to load.
Technical Information:
Fits: Lee 3 Hole, Classic 3 Hole Turret Press
Function: Replacement Turret
Notes: 7/8"-14 Threaded dies
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE SPLINE DRIVE BREECH LOCK BUSHING 4-PACK
Product Information
Spline drive Breech Lock Bushings 4 pack. New, easy grip splined drive surface allows easy, accurate and fast die installation in your press. Reloading dies are confusingly similar looking, so we anodized and colored the bushings so you can “color code” your dies for quick positive identification. No need for lock rings on your dies with these quick-change bushings. Simply lightly tighten the clamp screw, and split collar will put a vice lock on your die. Loosen the screw, and the die will spin freely. Once set you’ll never lose position. They look so good and work so well, you’ll want them for all your dies.
LEE SQUARE RATCHET
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
LEE STEEL BASE BLOCK FOR BENCH PLATE SYSTEM
Product Information:
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
RCBS Expander-Decapping Unit .375 cal
These replacement decapping units feature an expander rod, expander ball, and decapping pin. They are used in sizing dies to de-prime the case and expand the case neck in bottleneck cartridges. It is always a good idea to keep an extra decapping unit on-hand so you can ensure your reloading sessions do not get interrupted if you ever damage them during use.
- Factory Replacement Part
- Precision Machined to ensure concentricity
- Expander Rod, Expander Ball and Decapping Pin
- 0.375
- Limited Lifetime Warranty
