Hornady Match Grade Bushing .336 Diameter
$38.00
Product Information
For use with Hornady Match Grade Bushing Size Dies.
1 in stock
Related products
LEE – CASE COLLATOR FUNNEL
Product Information
The Lee Case Collator can fill all four Lee Case Feeder Tubes in just 10 seconds. Brass falls base down into the drop tubes, making progressive reloading with the Pro1000 or Load-Master presses that much easier. To use lay cases in collator and they will fall base down into the drop tubes (not included)
LEE – TURRET 3-HOLE FOR TURRET PRESS/PRO 1000
The Lee Turret Press is a proven design utilizing replaceable turrets that lock into a solid steel ring. One of the best features is the ability to simply lift out an entire turret and replace it with the another turret setup to load a different caliber. These extra turrets give reloaders the ability to have all of their different calibers on a different turret ready to load.
Technical Information:
Fits: Lee 3 Hole, Classic 3 Hole Turret Press
Function: Replacement Turret
Notes: 7/8"-14 Threaded dies
LEE APP BULGE BUSTER KIT w/o CARBIDE FACTORY CRIMP
Product Information
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
**Will work with the following cases:
- 380 ACP
- 10mm
- 40 S&W
- 41 AE (Use 40 S&W Factory Crimp Die)
- 45 ACP
- 45 GAP
- 45 Win Mag
The Lee Carbide Factory Crimp Die must be purchased separately.
LEE SQUARE RATCHET
Product Information
Part TF3567 for products: 90064 CLASSIC TURRET PRESS and 90932 4 HOLE TP WI AUTO INDEX.
This part installs inside the black auto index clamp on the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel index rod.
In order to maintain the integrity of the square ratchet, remember to raise the ram which disengages the ratchet from the housing and allows the index rod to spin freely. It is at this point that the Turret can be removed and installed at will. Put some household oil between the 4 hole turret and 4 hole turret ring to extend the life of your square ratchet.
LEE STEEL BASE BLOCK FOR BENCH PLATE SYSTEM
Product Information:
The Lee Reloading Bench Plate is the perfect accessory for the reloader looking to quickly change between presses on their reloading bench. The steel blank is constructed of sturdy steel, and has a black powder-coat finish for added durability. The blank has pre-drilled mounting holes that will accommodate all Lee metallic reloading presses manufactured after 2007. The base blank also has integral tabs built in on the sides to ensure proper plate retention and position in the Bench Plate, allowing you to switch presses quickly and easily on any bench or stand. This blank base only is a great addition to the Bench Plate Kit to allow the reloader to quickly swap between multiple presses or reloading equipment. Hardware for mounting one reloading press is included.
Notes: Blank is pre-drilled to fit all Lee metallic reloading presses manufactured after 2007.
LEE ULTIMATE LOCK RINGS 3-PACK
Product Information
Lee ultimate spline drive lock rings. 3 pack of gold anodized aluminum lock-rings with o-rings. One wouldn’t think you could improve on a simple thing like a lock ring, but we have. The new split clamp spline drive makes all other lock rings obsolete and clumsy to use. We started with custom extrusion of high strength aluminum with a splined exterior surface. We split the ring, and added a cross bolt that when even lightly tightened, applies a vice like grip on your dies. No tiny set screws that easily strip or damage your die threads. Then we added the famous Lee “O” ring because no matter how securely you have the lock ring clamped to the die, it will loosen in the press during operation without the friction of the “O” ring. The “O” ring allows you to finger tighten into your press and it will never loosen during operation yet you can easily remove your die with finger pressure. We have also included a handy slim profile lock ring wrench, works great when fitting dies on a turret or tool head. Dies are simply easier to install with the lock ring wrench.- Compatible with 7/8 x 14 threaded Lee reloading dies and Lee reloading presses.
- Torque type splined exterior, for a no-slip grip.
- "O" ring, anti-rotation, included. Never loosens during use.
- Lock-ring wrench included.
